← Commit history
README.md+69−71
@@ -8,22 +8,22 @@ A5366CLWTR-T from Allegro MicroSystems, LLC, in a SOIC-16. Pinout and pin descri  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | C1 | passive | Capacitor sets photoamplifier gain in supervisory (push-to-test and chamber monitor) mode, Ae = 1 + (C1/10) with C1 in pF, typically 0.047 µF and not above 0.1 µF. |-| 2 | C2 | passive | Capacitor sets photoamplifier gain in standby mode, Ae = 1 + (C2/10) with C2 in pF, typically 4700 pF and not above 0.1 µF, with a series resistor required. |-| 3 | DETECT | input | Photoamplifier input connected to the photodiode cathode, with the photodiode at zero bias and a shunt resistor in parallel. |-| 4 | STROBE | output | Strobed regulated output of VDD - 5 V that serves as the reference for the photoamplifier low side. |-| 5 | VDD | power_in | Positive supply voltage, 6 to 12 V with respect to VSS. |-| 6 | IRED | output | Pulsed base-current output for the external NPN transistor (beta above 100) that drives the IR emitter, inactive while horn and LED outputs are active. |-| 7 | I/O | bidirectional | Interconnect input/output for linking multiple detectors, with an on-chip pull-down, driven high on local smoke, and left unconnected if unused. |-| 8 | HORN1 | output | Piezoelectric horn drive output connected to the piezo metal support electrode, able to source 16 mA. |-| 9 | HORN2 | output | Complementary piezoelectric horn drive output connected to the ceramic electrode. |-| 10 | FEEDBACK | input | Horn feedback input connected to the piezo feedback electrode, tied to VSS if not used. |-| 11 | LED | output | Open-drain NMOS output driving the visible LED, which also loads the battery for the low-battery test, with a 500 to 1000 Ω resistor substituted if no LED is used. |-| 12 | OSC CAP | passive | Oscillator capacitor connection to VDD, with a parallel resistor, setting the internal clock low time as Tlow = 0.693 × R × C. |-| 13 | TIMING RES | passive | Resistor connection to OSC CAP that sets the clock high time (IRED pulse width), Thigh = 0.693 × R × C. |-| 14 | VSS | power_in | Negative supply potential, usually ground. |-| 15 | HUSH | input | Input with internal pull-down that enables timer mode above 1.5 V and disables it below 0.5 V, and sets the smoke comparator reference in timer mode. |-| 16 | TEST | input | Input with internal pull-down for push-to-test (about VDD - 0.5 V), diagnostic/calibration mode (pulled below VSS, 400 µA), and starting timer mode. |+| 1 | C1 | passive | Capacitor sets photoamplifier gain in supervisory mode, with Ae = 1 + (C1/10) with C1 in pF, and C1 should not exceed 0.1 µF. |+| 2 | C2 | passive | Capacitor sets photoamplifier gain in standby mode, with Ae = 1 + (C2/10) with C2 in pF, C2 should not exceed 0.1 µF, and a resistor must be installed in series with it. |+| 3 | DETECT | input | Photoamplifier input connected to the photodiode cathode, which is operated at zero bias and requires a shunt resistor in parallel. |+| 4 | STROBE | power_out | Strobed, regulated output of VDD - 5 V that serves as the low-side reference for the photoamplifier circuitry. |+| 5 | VDD | power_in | Positive supply pin that can range from 6 to 12 V with respect to VSS. |+| 6 | IRED | output | Pulsed base-current output for the external NPN transistor driving the IR emitter, whose beta should be greater than 100. |+| 7 | I/O | bidirectional | Interconnect pin that is driven high on local smoke and sampled every fourth clock cycle, requiring three consecutive high samples plus one additional cycle to alarm; it has an on-chip pull-down and must be left unconnected if unused. |+| 8 | HORN1 | output | Horn driver output connected to the piezoelectric transducer's metal support electrode. |+| 9 | HORN2 | output | Complementary horn driver output connected to the piezoelectric transducer's ceramic electrode. |+| 10 | FEEDBACK | input | Input connected to the piezoelectric feedback electrode, which must be connected to VSS if not used. |+| 11 | LED | output | Open-drain NMOS output that directly drives a visible LED; if no LED is used it should be replaced by an equivalent resistor (typically 500 to 1000 Ω) so battery loading stays about 10 mA. |+| 12 | OSC CAP | passive | Capacitor connection to VDD that, with a parallel resistor, sets the internal clock low time according to Tlow = 0.693 × ROSCCAP × COSCCAP. |+| 13 | TIMING RES | passive | Resistor connection to OSC CAP that sets the internal clock high time, which is also the IRED pulse width, according to Thigh = 0.693 × RTIMINGRES × COSCCAP. |+| 14 | VSS | power_in | Negative supply pin, connected to the negative supply potential (usually ground). |+| 15 | HUSH | input | Input with internal pull-down that enables timer mode when above 1.5 V and disables it when below 0.5 V, and also sets the smoke comparator reference during timer mode. |+| 16 | TEST | input | Input with internal pull-down that starts push-to-test when above approximately VDD - 0.5 V, starts timer mode on a high-to-low transition, and enters diagnostic test/calibration mode when pulled below VSS. |  ## Key specifications @@ -40,65 +40,63 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| Supply Voltage Range | VDD | 6 |  | 12 | V |  | 4 |-| Supply Voltage (abs max) | VDD | -0.5 |  | 15 | V | Referenced to VSS | 2 |-| Input Voltage Range (abs max) | VIN | -0.3 |  |  | V | Referenced to VSS; max printed as VDD+0.3 | 2 |+| Supply Voltage Range | VDD | -0.5 |  | 15 | V | Referenced to VSS | 2 |+| Input Voltage Range | VIN | -0.3 |  |  | V | Referenced to VSS; upper limit printed as VDD+0.3 V | 2 | | Input Current | IIN |  |  | 10 | mA |  | 2 | | Operating Ambient Temperature Range | TA | -25 |  | 75 | ºC |  | 2 | | Maximum Junction Temperature | TJ(max) |  |  | 150 | ºC |  | 2 | | Storage Temperature Range | Tstg | -55 |  | 125 | ºC |  | 2 |-| Package Thermal Resistance, Package LW | RθJA |  | 48 |  | ºC/W | Package LW, on 4-layer PCB based on JEDEC standard | 2 |-| Operating Supply Current, standby average | IDD |  |  | 9 | μA | Average in standby mode, configured per typical application; VDD = 12 V | 4 |-| Operating Supply Current, STROBE on, IRED off | IDD |  |  | 2 | mA | During STROBE on, IRED off, configured per typical application; VDD = 12 V | 4 |-| Operating Supply Current, STROBE on, IRED on | IDD |  |  | 3 | mA | During STROBE on, IRED on, configured per typical application; VDD = 12 V | 4 |-| Low-Level Input Voltage, I/O | VIL |  |  | 1.5 | V | Pin 7, VDD = 9 V | 4 |-| Low-Level Input Voltage, FEEDBACK | VIL |  |  | 2.7 | V | Pin 10, VDD = 9 V | 4 |-| Low-Level Input Voltage, TEST | VIL |  |  | 7 | V | Pin 16, VDD = 9 V | 4 |-| Low-Level Input Voltage, HUSH | VIL |  |  | 0.5 | V | Pin 15, VDD = 9 V | 4 |-| High-Level Input Voltage, I/O | VIH | 3.2 |  |  | V | Pin 7, VDD = 9 V | 4 |-| High-Level Input Voltage, FEEDBACK | VIH | 6.3 |  |  | V | Pin 10, VDD = 9 V | 4 |-| High-Level Input Voltage, TEST | VIH | 8.5 |  |  | V | Pin 16, VDD = 9 V | 4 |-| High-Level Input Voltage, HUSH | VIH | 1.6 |  |  | V | Pin 15, VDD = 9 V | 4 |-| Input Leakage High, C1/C2 | IIH |  |  | 100 | nA | VIN = VDD, STROBE active, OSC CAP = VDD; pins 1, 2; VDD = 12 V | 4 |-| Input Leakage High, DETECT/FEEDBACK/OSC CAP | IIH |  |  | 100 | nA | VIN = VDD; pins 3, 10, 12; VDD = 12 V | 4 |-| Input Leakage Low, pins 1-3 | IIL |  |  | -100 | nA | VIN = VST, STROBE active, OSC CAP = VDD; pins 1, 2, 3; VDD = 12 V | 4 |-| Input Leakage Low, pins 10, 12 | IIL |  |  | -100 | nA | VIN = VSS; pins 10, 12; VDD = 12 V | 4 |-| Input Leakage Low, pins 15, 16 | IIL |  |  | -1 | μA | VIN = VSS; pins 15, 16; VDD = 12 V | 4 |-| Input Pull-Down Current, TEST/HUSH | IIN | 0.25 |  | 10 | μA | VIN = VDD; pins 16, 15; VDD = 9 V | 4 |-| Input Pull-Down Current, I/O | IIN | 20 |  | 80 | μA | No local smoke, VIN = VDD; pin 7; VDD = 9 V | 4 |-| Input Pull-Down Current, I/O at 17 V | IIN |  |  | 140 | μA | No local smoke, VIN = 17 V; pin 7; VDD = 12 V | 4 |-| Low-Level Output Voltage, LED | VOL |  |  | 0.6 | V | IO = 10 mA; pin 11; VDD = 6.5 V | 4 |-| Low-Level Output Voltage, HORN1/HORN2 | VOL |  |  | 1 | V | IO = 16 mA; pins 8, 9; VDD = 6.5 V | 4 |-| High-Level Output Voltage | VOH | 5.5 |  |  | V | IO = -16 mA; pins 8, 9; VDD = 6.5 V | 4 |-| IRED Output Voltage, inactive | VIRED |  |  | 0.1 | V | Inactive, IO = 1 μA, TA = 25°C; pin 6; VDD = 12 V | 4 |-| IRED Output Voltage, active | VIRED | 2.85 | 3.1 | 3.35 | V | Active, IO = -6 mA, TA = 25°C; pin 6; VDD = 9 V | 4 |-| High-Level Output Current | IOH | -4 |  |  | mA | VDD = Alarm, I/O active, VO = VDD, 2 V; pin 7; VDD = 9 V | 5 |-| OFF Leakage Current High | IOZ |  |  | 1 | μA | VO = VDD; pins 11, 13; VDD = 12 V | 5 |-| OFF Leakage Current Low | IOZ |  |  | -1 | μA | VO = VSS; pins 11, 13; VDD = 12 V | 5 |+| Supply Voltage Range | VDD | 6 |  | 12 | V | Pin 5 | 4 |+| Operating Supply Current, average in standby mode | IDD |  |  | 9 | μA | Average in standby mode, configured per typical application; VDD 12 V; pin 5 | 4 |+| Operating Supply Current, STROBE on, IRED off | IDD |  |  | 2 | mA | During STROBE on, IRED off, configured per typical application; VDD 12 V; pin 5 | 4 |+| Operating Supply Current, STROBE on, IRED on | IDD |  |  | 3 | mA | During STROBE on, IRED on, configured per typical application; VDD 12 V; pin 5 | 4 |+| Low-Level Input Voltage | VIL |  |  | 1.5 | V | Test pin 7; VDD 9 V | 4 |+| Low-Level Input Voltage | VIL |  |  | 2.7 | V | Test pin 10; VDD 9 V | 4 |+| Low-Level Input Voltage | VIL |  |  | 7 | V | Test pin 16; VDD 9 V | 4 |+| Low-Level Input Voltage | VIL |  |  | 0.5 | V | Test pin 15; VDD 9 V | 4 |+| High-Level Input Voltage | VIH | 3.2 |  |  | V | Test pin 7; VDD 9 V | 4 |+| High-Level Input Voltage | VIH | 6.3 |  |  | V | Test pin 10; VDD 9 V | 4 |+| High-Level Input Voltage | VIH | 8.5 |  |  | V | Test pin 16; VDD 9 V | 4 |+| High-Level Input Voltage | VIH | 1.6 |  |  | V | Test pin 15; VDD 9 V | 4 |+| Input Leakage High | IIH |  |  | 100 | nA | VIN = VDD, STROBE active, OSC CAP = VDD; pins 1, 2; VDD 12 V | 4 |+| Input Leakage Low | IIL |  |  | -100 | nA | VIN = VST, STROBE active, OSC CAP = VDD; pins 1, 2, 3; VDD 12 V | 4 |+| Input Leakage Low | IIL |  |  | -1 | μA | VIN = VSS; pins 15, 16; VDD 12 V | 4 |+| Input Pull-Down Current | IIN | 0.25 |  | 10 | μA | VIN = VDD; pins 16, 15; VDD 9 V | 4 |+| Input Pull-Down Current | IIN | 20 |  | 80 | μA | No local smoke, VIN = VDD; pin 7; VDD 9 V | 4 |+| Input Pull-Down Current | IIN |  |  | 140 | μA | No local smoke, VIN = 17 V; pin 7; VDD 12 V | 4 |+| Low-Level Output Voltage | VOL |  |  | 0.6 | V | IO = 10 mA; pin 11; VDD 6.5 V | 4 |+| Low-Level Output Voltage | VOL |  |  | 1 | V | IO = 16 mA; pins 8, 9; VDD 6.5 V | 4 |+| High-Level Output Voltage | VOH | 5.5 |  |  | V | IO = -16 mA; pins 8, 9; VDD 6.5 V | 4 |+| IRED Output Voltage, inactive | VIRED |  |  | 0.1 | V | Inactive, IO = 1 μA, TA = 25°C; pin 6; VDD 12 V | 4 |+| IRED Output Voltage, active | VIRED | 2.85 | 3.1 | 3.35 | V | Active, IO = -6 mA, TA = 25°C; pin 6; VDD 9 V | 4 |+| OFF Leakage Current High | IOZ |  |  | 1 | μA | VO = VDD; pins 11, 13; VDD 12 V | 5 |+| OFF Leakage Current Low | IOZ |  |  | -1 | μA | VO = VSS; pins 11, 13; VDD 12 V | 5 |+| High-Level Output Current | IOH | -4 |  |  | mA | VDD = Alarm, I/O active, VO = VDD, 2 V; pin 7; VDD 9 V | 5 | | Low-Battery Alarm Threshold | VDD(th) | 6.9 | 7.2 | 7.5 | V | Pin 5 | 5 |-| Oscillator Period | tosc | 9.4 | 10.5 | 11.5 | ms | Pin 12; VDD = 9 V | 5 |-| LED Pulse Period, no smoke | tled1 | 39 |  | 48 | s | No local or remote smoke; pin 11; VDD = 9 V | 5 |-| LED Pulse Period, local smoke | tled3 | 0.45 | 0.5 | 0.55 | s | Local smoke; pin 11; VDD = 9 V | 5 |-| LED Pulse Period, pushbutton test | tled6 | 0.45 | 0.5 | 0.55 | s | Pushbutton test, induced alarm; pin 11; VDD = 9 V | 5 |-| LED Pulse Period, timer mode | tled7 | 9.67 | 10.75 | 11.83 | s | Timer mode, no alarm; pin 11; VDD = 9 V | 5 |-| LED Pulse Width | tw(led) | 9.5 |  | 11.5 | ms | Pin 11; VDD = 9 V | 5 |-| STROBE Pulse Period, no smoke | tst1 | 9.6 |  | 11.9 | s | No local or remote smoke; pin 4; VDD = 9 V | 5 |-| STROBE Pulse Period, 1 of 3 samples | tst2 | 1.8 | 2 | 2.2 | s | After 1 of 3 valid samples; pin 4; VDD = 9 V | 5 |-| STROBE Pulse Period, 2 of 3 samples | tst3 | 0.8 | 1 | 1.1 | s | After 2 of 3 valid samples and during local alarm; pin 4; VDD = 9 V | 5 |-| STROBE Pulse Period, remote smoke | tst4 | 7.2 | 8 | 8.9 | s | Remote smoke only; pin 4; VDD = 9 V | 5 |-| STROBE Pulse Period, chamber/low battery test | tst5 | 38.9 |  | 47.1 | s | Chamber test or low battery test, no local alarm; pin 4; VDD = 9 V | 5 |-| STROBE Pulse Period, pushbutton test | tst6 | 225 | 252 | 278 | ms | Pushbutton test, induced alarm; pin 4; VDD = 9 V | 5 |-| STROBE Pulse Width | tw(st) | 9.5 |  | 11.5 | ms | Pin 4; VDD = 9 V | 5 |-| IRED Pulse Period, no smoke | tired1 | 9.6 |  | 11.9 | s | No local or remote smoke; pin 6; VDD = 9 V | 6 |-| IRED Pulse Width | tw(ired) | 94 |  | 116 | μs | Pin 6; VDD = 9 V | 6 |-| IRED Rise Time | tr(ired) |  |  | 30 | μs | 10% to 90%; pin 6 | 6 |-| IRED Fall Time | tf(ired) |  |  | 200 | μs | 90% to 10%; pin 6 | 6 |-| I/O Charge Dump Duration | tdump | 0.9 | 1 | 1.1 | s | End of local alarm or test; pin 7; VDD = 9 V | 6 |-| Horn Warning Pulse Period | thorn | 38.9 |  | 47.1 | s | Low battery or degraded chamber sensitivity; pins 8, 9; VDD = 9 V | 6 |-| Horn Warning Pulse Width | tw(horn) | 9.5 |  | 11.5 | ms | Low battery or degraded chamber sensitivity; pins 8, 9; VDD = 9 V | 6 |-| Horn On-Time | ton(horn) | 450 | 500 | 550 | ms | Local or remote alarm; pins 8, 9; VDD = 9 V | 6 |-| Horn Off-Time 1 | toff1(horn) | 450 | 500 | 550 | ms | Local or remote alarm (see Timing Diagrams section); pins 8, 9; VDD = 9 V | 6 |-| Horn Off-Time 2 | toff2(horn) | 1350 | 1500 | 1650 | ms | Local or remote alarm (see Timing Diagrams section); pins 8, 9; VDD = 9 V | 6 |+| Oscillator Period | tosc | 9.4 | 10.5 | 11.5 | ms | Pin 12; VDD 9 V | 5 |+| LED Pulse Period | tled1 | 39 |  | 48 | s | No local or remote smoke; pin 11; VDD 9 V | 5 |+| LED Pulse Period | tled3 | 0.45 | 0.5 | 0.55 | s | Local smoke; pin 11; VDD 9 V | 5 |+| LED Pulse Period | tled7 | 9.67 | 10.75 | 11.83 | s | Timer mode, no alarm; pin 11; VDD 9 V | 5 |+| STROBE Pulse Period | tst1 | 9.6 |  | 11.9 | s | No local or remote smoke; pin 4; VDD 9 V | 5 |+| STROBE Pulse Period | tst2 | 1.8 | 2 | 2.2 | s | After 1 of 3 valid samples; pin 4; VDD 9 V | 5 |+| STROBE Pulse Period | tst3 | 0.8 | 1 | 1.1 | s | After 2 of 3 valid samples and during local alarm; pin 4; VDD 9 V | 5 |+| STROBE Pulse Period | tst4 | 7.2 | 8 | 8.9 | s | Remote smoke only; pin 4; VDD 9 V | 5 |+| STROBE Pulse Period | tst5 | 38.9 |  | 47.1 | s | Chamber test or low battery test, no local alarm; pin 4; VDD 9 V | 5 |+| STROBE Pulse Period | tst6 | 225 | 252 | 278 | ms | Pushbutton test, induced alarm; pin 4; VDD 9 V | 5 |+| STROBE Pulse Width | tw(st) | 9.5 |  | 11.5 | ms | Pin 4; VDD 9 V | 5 |+| IRED Pulse Period | tired1 | 9.6 |  | 11.9 | s | No local or remote smoke; pin 6; VDD 9 V | 6 |+| IRED Pulse Period | tired2 | 1.8 | 2 | 2.2 | s | After 1 of 3 valid samples; pin 6; VDD 9 V | 6 |+| IRED Pulse Period | tired3 | 0.8 | 1 | 1.1 | s | After 2 of 3 valid samples and during local alarm; pin 6; VDD 9 V | 6 |+| IRED Pulse Period | tired4 | 7.2 | 8 | 8.9 | s | Remote smoke only; pin 6; VDD 9 V | 6 |+| IRED Pulse Period | tired5 | 38.9 |  | 47.1 | s | Chamber test, no local alarm; pin 6; VDD 9 V | 6 |+| IRED Pulse Period | tired6 | 225 | 252 | 278 | ms | Pushbutton test, induced alarm; pin 6; VDD 9 V | 6 |+| IRED Pulse Width | tw(ired) | 94 |  | 116 | μs | Pin 6; VDD 9 V | 6 |+| I/O Charge Dump Duration | tdump | 0.9 | 1 | 1.1 | s | End of local alarm or test; pin 7; VDD 9 V | 6 |+| Horn Warning Pulse Period | thorn | 38.9 |  | 47.1 | s | Low battery or degraded chamber sensitivity; pins 8, 9; VDD 9 V | 6 |+| Horn On-Time | ton(horn) | 450 | 500 | 550 | ms | Local or remote alarm; pins 8, 9; VDD 9 V | 6 |+| Horn Off-Time | toff1(horn) | 450 | 500 | 550 | ms | Local or remote alarm (see Timing Diagrams section); pins 8, 9; VDD 9 V | 6 |+| Horn Off-Time | toff2(horn) | 1350 | 1500 | 1650 | ms | Local or remote alarm (see Timing Diagrams section); pins 8, 9; VDD 9 V | 6 |+| Package Thermal Resistance, package LW | RθJA |  | 48 |  | ºC/W | Package LW, on 4-layer PCB based on JEDEC standard | 2 |  ## Materials and finish @@ -120,7 +118,7 @@ As the datasheet states them (page.json `metadata.appearance`; the 3D model's co Data extracted from the manufacturer datasheet, not a distributor listing:  - **Datasheet:** [Allegro MicroSystems, LLC datasheet](docs/a5366clwtr-t-datasheet.pdf) (13 pp, sha256 `a14bc986d595aa2d`, retrieved 2026-11-12, tier: lcsc)-- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** KiCad official libraries (CC-BY-SA 4.0).  [Datasheet PDF](docs/a5366clwtr-t-datasheet.pdf)
a5366clwtr-t-hero.overlay.json+439−434
@@ -1,436 +1,441 @@ {-  "spec": "adom-hero 1.4",-  "mpn": "A5366CLWTR-T",-  "kind": "component + footprint reference art",-  "board_use": false,-  "plane_z_mm": -0.02,-  "units": "metre",-  "upAxis": "Z",-  "layers": {-    "pad_outlines": {-      "material": "Footprint pads - teal dashed outlines - 50 percent opacity",-      "rgba": [-        0.0,-        0.902,-        0.863,-        0.5-      ],-      "pads": 16,-      "span_mm": 11.35,-      "dash_mm": 0.2838,-      "gap_mm": 0.1703,-      "pad_stroke_mm": 0.0681-    },-    "silkscreen": {-      "material": "Silkscreen reference lines - 30 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.3-      ],-      "footprint_items": 7,-      "pin1": {-        "source": "footprint silkscreen",-        "pad": "1"-      }-    },-    "signal_names": {-      "material": "Signal names - 50 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.5-      ],-      "font": "DejaVu Sans Mono",-      "labels": 16,-      "sides": "top + mirrored underside (single-sided)",-      "fallback_to_pad_number": 0-    }-  },-  "align": {-    "ok": true,-    "centre_offset_mm": 0.0,-    "tolerance_mm": 0.908,-    "orientation_flipped": false,-    "contacts_bbox_mm": [-      -5.15,-      5.15,-      -4.65,-      4.65-    ],-    "pads_bbox_mm": [-      -5.675,-      5.675,-      -4.745,-      4.745-    ],-    "seating_z_mm": -0.0-  },-  "sources": {-    "glb": "a5366clwtr-t-etched.glb",-    "glb_sha256": "5fe8dec79d17adecbb1708fe6d10771864d16e0acdb984383e0da84f451bd221",-    "footprint": "a5366clwtr-t.kicad_mod",-    "footprint_sha256": "07aa02ced9fcdc61d7c6bb5ea1b86803731041e9e171db91a991c3daa7817383",-    "pins": "page.json component.pins",-    "pins_sha256": "d3f48664627a52fd9728fd8e5da68887e80a8f20cc210b1cf3c8e632fd431ce1"-  },-  "generator": "adom-wiki 1.8.22 (component_hero)",-  "labels": [-    {-      "pad": "1",-      "text": "C1",-      "x": -5.825,-      "y": -4.445,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "2",-      "text": "C2",-      "x": -5.825,-      "y": -3.175,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "3",-      "text": "DETECT",-      "x": -5.825,-      "y": -1.905,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "4",-      "text": "STROBE",-      "x": -5.825,-      "y": -0.635,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "5",-      "text": "VDD",-      "x": -5.825,-      "y": 0.635,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "6",-      "text": "IRED",-      "x": -5.825,-      "y": 1.905,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "7",-      "text": "I/O",-      "x": -5.825,-      "y": 3.175,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "8",-      "text": "HORN1",-      "x": -5.825,-      "y": 4.445,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "9",-      "text": "HORN2",-      "x": 5.825,-      "y": 4.445,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "10",-      "text": "FEEDBACK",-      "x": 5.825,-      "y": 3.175,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "11",-      "text": "LED",-      "x": 5.825,-      "y": 1.905,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "12",-      "text": "OSC CAP",-      "x": 5.825,-      "y": 0.635,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "13",-      "text": "TIMING RES",-      "x": 5.825,-      "y": -0.635,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "14",-      "text": "VSS",-      "x": 5.825,-      "y": -1.905,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "15",-      "text": "HUSH",-      "x": 5.825,-      "y": -3.175,-      "align": "left",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "16",-      "text": "TEST",-      "x": 5.825,-      "y": -4.445,-      "align": "left",-      "vertical": false,-      "h": 0.6-    }+ "spec": "adom-hero 1.4",+ "mpn": "A5366CLWTR-T",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+  "pad_outlines": {+   "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+   "rgba": [+    0.0,+    0.902,+    0.863,+    0.5+   ],+   "pads": 16,+   "span_mm": 11.35,+   "dash_mm": 0.2838,+   "gap_mm": 0.1703,+   "pad_stroke_mm": 0.0681+  },+  "silkscreen": {+   "material": "Silkscreen reference lines - 30 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.3+   ],+   "footprint_items": 7,+   "pin1": {+    "source": "footprint silkscreen",+    "pad": "1"+   }+  },+  "signal_names": {+   "material": "Signal names - 50 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.5+   ],+   "font": "DejaVu Sans Mono",+   "labels": 16,+   "sides": "top + mirrored underside (single-sided)",+   "omitted": null,+   "fallback_to_pad_number": 0+  }+ },+ "align": {+  "ok": true,+  "board_underside": true,+  "electrical_pads_without_contact": [],+  "mounting_pads_left_out": [],+  "centre_offset_mm": 0.0,+  "over_pads": true,+  "tolerance_mm": 0.908,+  "orientation_flipped": false,+  "contacts_bbox_mm": [+   -5.15,+   5.15,+   -4.65,+   4.65+  ],+  "pads_bbox_mm": [+   -5.675,+   5.675,+   -4.745,+   4.745   ],-  "pads": [-    {-      "number": "1",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        -4.445-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "2",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        -3.175-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "3",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        -1.905-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "4",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        -0.635-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "5",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        0.635-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "6",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        1.905-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "7",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        3.175-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "8",-      "shape": "roundrect",-      "center_mm": [-        -4.65,-        4.445-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "9",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        4.445-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "10",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        3.175-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "11",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        1.905-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "12",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        0.635-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "13",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        -0.635-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "14",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        -1.905-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "15",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        -3.175-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    },-    {-      "number": "16",-      "shape": "roundrect",-      "center_mm": [-        4.65,-        -4.445-      ],-      "size_mm": [-        2.05,-        0.6-      ],-      "rot": 0.0-    }-  ]-}+  "seating_z_mm": -0.0+ },+ "sources": {+  "glb": "a5366clwtr-t-etched.glb",+  "glb_sha256": "5fe8dec79d17adecbb1708fe6d10771864d16e0acdb984383e0da84f451bd221",+  "footprint": "a5366clwtr-t.kicad_mod",+  "footprint_sha256": "07aa02ced9fcdc61d7c6bb5ea1b86803731041e9e171db91a991c3daa7817383",+  "pins": "page.json component.pins",+  "pins_sha256": "d3f48664627a52fd9728fd8e5da68887e80a8f20cc210b1cf3c8e632fd431ce1"+ },+ "generator": "factory/hero_glb.py",+ "labels": [+  {+   "pad": "1",+   "text": "C1",+   "x": -5.825,+   "y": -4.445,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "2",+   "text": "C2",+   "x": -5.825,+   "y": -3.175,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "3",+   "text": "DETECT",+   "x": -5.825,+   "y": -1.905,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "4",+   "text": "STROBE",+   "x": -5.825,+   "y": -0.635,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "5",+   "text": "VDD",+   "x": -5.825,+   "y": 0.635,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "6",+   "text": "IRED",+   "x": -5.825,+   "y": 1.905,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "7",+   "text": "I/O",+   "x": -5.825,+   "y": 3.175,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "8",+   "text": "HORN1",+   "x": -5.825,+   "y": 4.445,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "9",+   "text": "HORN2",+   "x": 5.825,+   "y": 4.445,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "10",+   "text": "FEEDBACK",+   "x": 5.825,+   "y": 3.175,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "11",+   "text": "LED",+   "x": 5.825,+   "y": 1.905,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "12",+   "text": "OSC CAP",+   "x": 5.825,+   "y": 0.635,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "13",+   "text": "TIMING RES",+   "x": 5.825,+   "y": -0.635,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "14",+   "text": "VSS",+   "x": 5.825,+   "y": -1.905,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "15",+   "text": "HUSH",+   "x": 5.825,+   "y": -3.175,+   "align": "left",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "16",+   "text": "TEST",+   "x": 5.825,+   "y": -4.445,+   "align": "left",+   "vertical": false,+   "h": 0.6+  }+ ],+ "pads": [+  {+   "number": "1",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    -4.445+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "2",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    -3.175+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "3",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    -1.905+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "4",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    -0.635+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "5",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    0.635+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "6",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    1.905+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "7",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    3.175+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "8",+   "shape": "roundrect",+   "center_mm": [+    -4.65,+    4.445+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "9",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    4.445+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "10",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    3.175+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "11",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    1.905+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "12",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    0.635+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "13",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    -0.635+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "14",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    -1.905+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "15",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    -3.175+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  },+  {+   "number": "16",+   "shape": "roundrect",+   "center_mm": [+    4.65,+    -4.445+   ],+   "size_mm": [+    2.05,+    0.6+   ],+   "rot": 0.0+  }+ ]+}\ No newline at end of file
a5366clwtr-t.kicad_sym+1−1
@@ -20,7 +20,7 @@       (name "DETECT" (effects (font (size 1.27 1.27))))       (number "3" (effects (font (size 1.27 1.27))))     )-    (pin output line (at -17.78 0.00 0) (length 5.08)+    (pin power_out line (at -17.78 0.00 0) (length 5.08)       (name "STROBE" (effects (font (size 1.27 1.27))))       (number "4" (effects (font (size 1.27 1.27))))     )
package.json+30−30
@@ -1,6 +1,6 @@ {   "slug": "a5366clwtr-t",-  "version": "0.1.0",+  "version": "0.1.1",   "type": "component",   "description": "Allegro MicroSystems, LLC Interface - Specialized, SOIC-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -54,7 +54,7 @@       "mouser": "250-A5366CLWTR-T"     },     "distributor_check": {-      "checked_at": "2026-11-12T04:58:15Z",+      "checked_at": "2026-11-12T08:00:24Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "A5366CLWTR-T-ND",@@ -70,97 +70,97 @@         "number": "1",         "name": "C1",         "type": "passive",-        "description": "Capacitor sets photoamplifier gain in supervisory (push-to-test and chamber monitor) mode, Ae = 1 + (C1/10) with C1 in pF, typically 0.047 µF and not above 0.1 µF."+        "description": "Capacitor sets photoamplifier gain in supervisory mode, with Ae = 1 + (C1/10) with C1 in pF, and C1 should not exceed 0.1 µF."       },       {         "number": "2",         "name": "C2",         "type": "passive",-        "description": "Capacitor sets photoamplifier gain in standby mode, Ae = 1 + (C2/10) with C2 in pF, typically 4700 pF and not above 0.1 µF, with a series resistor required."+        "description": "Capacitor sets photoamplifier gain in standby mode, with Ae = 1 + (C2/10) with C2 in pF, C2 should not exceed 0.1 µF, and a resistor must be installed in series with it."       },       {         "number": "3",         "name": "DETECT",         "type": "input",-        "description": "Photoamplifier input connected to the photodiode cathode, with the photodiode at zero bias and a shunt resistor in parallel."+        "description": "Photoamplifier input connected to the photodiode cathode, which is operated at zero bias and requires a shunt resistor in parallel."       },       {         "number": "4",         "name": "STROBE",-        "type": "output",-        "description": "Strobed regulated output of VDD - 5 V that serves as the reference for the photoamplifier low side."+        "type": "power_out",+        "description": "Strobed, regulated output of VDD - 5 V that serves as the low-side reference for the photoamplifier circuitry."       },       {         "number": "5",         "name": "VDD",         "type": "power_in",-        "description": "Positive supply voltage, 6 to 12 V with respect to VSS."+        "description": "Positive supply pin that can range from 6 to 12 V with respect to VSS."       },       {         "number": "6",         "name": "IRED",         "type": "output",-        "description": "Pulsed base-current output for the external NPN transistor (beta above 100) that drives the IR emitter, inactive while horn and LED outputs are active."+        "description": "Pulsed base-current output for the external NPN transistor driving the IR emitter, whose beta should be greater than 100."       },       {         "number": "7",         "name": "I/O",         "type": "bidirectional",-        "description": "Interconnect input/output for linking multiple detectors, with an on-chip pull-down, driven high on local smoke, and left unconnected if unused."+        "description": "Interconnect pin that is driven high on local smoke and sampled every fourth clock cycle, requiring three consecutive high samples plus one additional cycle to alarm; it has an on-chip pull-down and must be left unconnected if unused."       },       {         "number": "8",         "name": "HORN1",         "type": "output",-        "description": "Piezoelectric horn drive output connected to the piezo metal support electrode, able to source 16 mA."+        "description": "Horn driver output connected to the piezoelectric transducer's metal support electrode."       },       {         "number": "9",         "name": "HORN2",         "type": "output",-        "description": "Complementary piezoelectric horn drive output connected to the ceramic electrode."+        "description": "Complementary horn driver output connected to the piezoelectric transducer's ceramic electrode."       },       {         "number": "10",         "name": "FEEDBACK",         "type": "input",-        "description": "Horn feedback input connected to the piezo feedback electrode, tied to VSS if not used."+        "description": "Input connected to the piezoelectric feedback electrode, which must be connected to VSS if not used."       },       {         "number": "11",         "name": "LED",         "type": "output",-        "description": "Open-drain NMOS output driving the visible LED, which also loads the battery for the low-battery test, with a 500 to 1000 Ω resistor substituted if no LED is used."+        "description": "Open-drain NMOS output that directly drives a visible LED; if no LED is used it should be replaced by an equivalent resistor (typically 500 to 1000 Ω) so battery loading stays about 10 mA."       },       {         "number": "12",         "name": "OSC CAP",         "type": "passive",-        "description": "Oscillator capacitor connection to VDD, with a parallel resistor, setting the internal clock low time as Tlow = 0.693 × R × C."+        "description": "Capacitor connection to VDD that, with a parallel resistor, sets the internal clock low time according to Tlow = 0.693 × ROSCCAP × COSCCAP."       },       {         "number": "13",         "name": "TIMING RES",         "type": "passive",-        "description": "Resistor connection to OSC CAP that sets the clock high time (IRED pulse width), Thigh = 0.693 × R × C."+        "description": "Resistor connection to OSC CAP that sets the internal clock high time, which is also the IRED pulse width, according to Thigh = 0.693 × RTIMINGRES × COSCCAP."       },       {         "number": "14",         "name": "VSS",         "type": "power_in",-        "description": "Negative supply potential, usually ground."+        "description": "Negative supply pin, connected to the negative supply potential (usually ground)."       },       {         "number": "15",         "name": "HUSH",         "type": "input",-        "description": "Input with internal pull-down that enables timer mode above 1.5 V and disables it below 0.5 V, and sets the smoke comparator reference in timer mode."+        "description": "Input with internal pull-down that enables timer mode when above 1.5 V and disables it when below 0.5 V, and also sets the smoke comparator reference during timer mode."       },       {         "number": "16",         "name": "TEST",         "type": "input",-        "description": "Input with internal pull-down for push-to-test (about VDD - 0.5 V), diagnostic/calibration mode (pulled below VSS, 400 µA), and starting timer mode."+        "description": "Input with internal pull-down that starts push-to-test when above approximately VDD - 0.5 V, starts timer mode on a high-to-low transition, and enters diagnostic test/calibration mode when pulled below VSS."       }     ],     "provenance": {@@ -168,18 +168,18 @@       "factory_chain": {         "factory": "2.0.0",         "extractor": "extract_pins 0.3",-        "primary_model": "claude-sonnet-5-5",+        "primary_model": "claude-haiku-5-5",         "primary_mode": "text",         "consensus_model": "claude-sonnet-5-5",         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: Pin types are inferred from the functional descriptions, since the datasheet gives no electrical typ",+          "extractor flagged: Pin numbers and names were taken from the 'Terminal List Table' on page 2 for the Package LW (16-pin; The datasheet does not state a KiCad ERC class for each pin. Types for C1, C2, OSC CAP and TIMING RE; Pin descriptions were condensed to one sentence each from the Pin and Circuit Description section (p",           "3/16 pins cited to the wrong page (name found elsewhere): ['14:VSS@p8', '15:HUSH@p8', '16:TEST@p8']"         ],         "pages_sent": 13,-        "cost_usd": 0.1418,-        "at": "2026-11-12T04:58:04"+        "cost_usd": 0.0763,+        "at": "2026-11-12T07:59:54"       },       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/1fb5fc0f8cc2d6e133de8e134e92d397.pdf",@@ -234,7 +234,7 @@         "zmin_mm": -0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "ea904ab24a54b0f8b6142c0455d94eb503ba1dbccaedf0bd40b9e5cc2303d864",+        "sha256": "eed552f7317fd69ef5971958229151d81382645d65c19b10494717e4e6fad34c",         "checked": "2026-11-12",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }@@ -245,22 +245,22 @@       "D": {         "nom_mm": 10.3,         "range_mm": [-          null,-          null+          10.1,+          10.5         ]       },       "E1": {         "nom_mm": 7.5,         "range_mm": [-          null,-          null+          7.4,+          7.6         ]       },       "E": {         "nom_mm": 10.3,         "range_mm": [-          null,-          null+          9.97,+          10.63         ]       },       "e": {
page.json+33−31
@@ -4,7 +4,7 @@   "slug": "a5366clwtr-t",   "title": "A5366CLWTR-T",   "brief": "Allegro MicroSystems, LLC Interface - Specialized, SOIC-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.1.1",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -36,7 +36,7 @@       "mouser": "250-A5366CLWTR-T"     },     "distributor_check": {-      "checked_at": "2026-11-12T04:58:15Z",+      "checked_at": "2026-11-12T08:00:24Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "A5366CLWTR-T-ND",@@ -52,97 +52,97 @@         "number": "1",         "name": "C1",         "type": "passive",-        "description": "Capacitor sets photoamplifier gain in supervisory (push-to-test and chamber monitor) mode, Ae = 1 + (C1/10) with C1 in pF, typically 0.047 µF and not above 0.1 µF."+        "description": "Capacitor sets photoamplifier gain in supervisory mode, with Ae = 1 + (C1/10) with C1 in pF, and C1 should not exceed 0.1 µF."       },       {         "number": "2",         "name": "C2",         "type": "passive",-        "description": "Capacitor sets photoamplifier gain in standby mode, Ae = 1 + (C2/10) with C2 in pF, typically 4700 pF and not above 0.1 µF, with a series resistor required."+        "description": "Capacitor sets photoamplifier gain in standby mode, with Ae = 1 + (C2/10) with C2 in pF, C2 should not exceed 0.1 µF, and a resistor must be installed in series with it."       },       {         "number": "3",         "name": "DETECT",         "type": "input",-        "description": "Photoamplifier input connected to the photodiode cathode, with the photodiode at zero bias and a shunt resistor in parallel."+        "description": "Photoamplifier input connected to the photodiode cathode, which is operated at zero bias and requires a shunt resistor in parallel."       },       {         "number": "4",         "name": "STROBE",-        "type": "output",-        "description": "Strobed regulated output of VDD - 5 V that serves as the reference for the photoamplifier low side."+        "type": "power_out",+        "description": "Strobed, regulated output of VDD - 5 V that serves as the low-side reference for the photoamplifier circuitry."       },       {         "number": "5",         "name": "VDD",         "type": "power_in",-        "description": "Positive supply voltage, 6 to 12 V with respect to VSS."+        "description": "Positive supply pin that can range from 6 to 12 V with respect to VSS."       },       {         "number": "6",         "name": "IRED",         "type": "output",-        "description": "Pulsed base-current output for the external NPN transistor (beta above 100) that drives the IR emitter, inactive while horn and LED outputs are active."+        "description": "Pulsed base-current output for the external NPN transistor driving the IR emitter, whose beta should be greater than 100."       },       {         "number": "7",         "name": "I/O",         "type": "bidirectional",-        "description": "Interconnect input/output for linking multiple detectors, with an on-chip pull-down, driven high on local smoke, and left unconnected if unused."+        "description": "Interconnect pin that is driven high on local smoke and sampled every fourth clock cycle, requiring three consecutive high samples plus one additional cycle to alarm; it has an on-chip pull-down and must be left unconnected if unused."       },       {         "number": "8",         "name": "HORN1",         "type": "output",-        "description": "Piezoelectric horn drive output connected to the piezo metal support electrode, able to source 16 mA."+        "description": "Horn driver output connected to the piezoelectric transducer's metal support electrode."       },       {         "number": "9",         "name": "HORN2",         "type": "output",-        "description": "Complementary piezoelectric horn drive output connected to the ceramic electrode."+        "description": "Complementary horn driver output connected to the piezoelectric transducer's ceramic electrode."       },       {         "number": "10",         "name": "FEEDBACK",         "type": "input",-        "description": "Horn feedback input connected to the piezo feedback electrode, tied to VSS if not used."+        "description": "Input connected to the piezoelectric feedback electrode, which must be connected to VSS if not used."       },       {         "number": "11",         "name": "LED",         "type": "output",-        "description": "Open-drain NMOS output driving the visible LED, which also loads the battery for the low-battery test, with a 500 to 1000 Ω resistor substituted if no LED is used."+        "description": "Open-drain NMOS output that directly drives a visible LED; if no LED is used it should be replaced by an equivalent resistor (typically 500 to 1000 Ω) so battery loading stays about 10 mA."       },       {         "number": "12",         "name": "OSC CAP",         "type": "passive",-        "description": "Oscillator capacitor connection to VDD, with a parallel resistor, setting the internal clock low time as Tlow = 0.693 × R × C."+        "description": "Capacitor connection to VDD that, with a parallel resistor, sets the internal clock low time according to Tlow = 0.693 × ROSCCAP × COSCCAP."       },       {         "number": "13",         "name": "TIMING RES",         "type": "passive",-        "description": "Resistor connection to OSC CAP that sets the clock high time (IRED pulse width), Thigh = 0.693 × R × C."+        "description": "Resistor connection to OSC CAP that sets the internal clock high time, which is also the IRED pulse width, according to Thigh = 0.693 × RTIMINGRES × COSCCAP."       },       {         "number": "14",         "name": "VSS",         "type": "power_in",-        "description": "Negative supply potential, usually ground."+        "description": "Negative supply pin, connected to the negative supply potential (usually ground)."       },       {         "number": "15",         "name": "HUSH",         "type": "input",-        "description": "Input with internal pull-down that enables timer mode above 1.5 V and disables it below 0.5 V, and sets the smoke comparator reference in timer mode."+        "description": "Input with internal pull-down that enables timer mode when above 1.5 V and disables it when below 0.5 V, and also sets the smoke comparator reference during timer mode."       },       {         "number": "16",         "name": "TEST",         "type": "input",-        "description": "Input with internal pull-down for push-to-test (about VDD - 0.5 V), diagnostic/calibration mode (pulled below VSS, 400 µA), and starting timer mode."+        "description": "Input with internal pull-down that starts push-to-test when above approximately VDD - 0.5 V, starts timer mode on a high-to-low transition, and enters diagnostic test/calibration mode when pulled below VSS."       }     ],     "provenance": {@@ -150,18 +150,18 @@       "factory_chain": {         "factory": "2.0.0",         "extractor": "extract_pins 0.3",-        "primary_model": "claude-sonnet-5-5",+        "primary_model": "claude-haiku-5-5",         "primary_mode": "text",         "consensus_model": "claude-sonnet-5-5",         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: Pin types are inferred from the functional descriptions, since the datasheet gives no electrical typ",+          "extractor flagged: Pin numbers and names were taken from the 'Terminal List Table' on page 2 for the Package LW (16-pin; The datasheet does not state a KiCad ERC class for each pin. Types for C1, C2, OSC CAP and TIMING RE; Pin descriptions were condensed to one sentence each from the Pin and Circuit Description section (p",           "3/16 pins cited to the wrong page (name found elsewhere): ['14:VSS@p8', '15:HUSH@p8', '16:TEST@p8']"         ],         "pages_sent": 13,-        "cost_usd": 0.1418,-        "at": "2026-11-12T04:58:04"+        "cost_usd": 0.0763,+        "at": "2026-11-12T07:59:54"       },       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/1fb5fc0f8cc2d6e133de8e134e92d397.pdf",@@ -216,7 +216,7 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "ea904ab24a54b0f8b6142c0455d94eb503ba1dbccaedf0bd40b9e5cc2303d864",+        "sha256": "eed552f7317fd69ef5971958229151d81382645d65c19b10494717e4e6fad34c",         "checked": "2026-11-12",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }@@ -227,22 +227,22 @@       "D": {         "nom_mm": 10.3,         "range_mm": [-          null,-          null+          10.1,+          10.5         ]       },       "E1": {         "nom_mm": 7.5,         "range_mm": [-          null,-          null+          7.4,+          7.6         ]       },       "E": {         "nom_mm": 10.3,         "range_mm": [-          null,-          null+          9.97,+          10.63         ]       },       "e": {@@ -1042,5 +1042,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "Allegro MicroSystems, LLC Interface - Specialized, SOIC-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file