← Commit history

Initial commit: component/a4915mettr-t

Ray ·3aa79aa953 ·
2 files changed +335
README.mdadded+65
@@ -0,0 +1,65 @@+# A4915METTR-T++**Allegro MicroSystems LLC** · Brushless DC (BLDC) Motor Driver · QFN-28-EP(5x5)++A4915METTR-T from Allegro MicroSystems LLC, in a QFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VBB | power_in | Power supply input, 5 V to 50 V operating range |+| 2 | SPEED | input | PWM duty cycle analog input, 0 V to VDD; output enabled above 79% VDD, disabled below 20% VDD |+| 3 | TDEAD | input | Dead time setting terminal with external resistor 12 kΩ to 220 kΩ connected to ground |+| 4 | VDD | power_in | Logic supply voltage input, 3 V to 5.5 V operating range |+| 5 | FAULT | output | Open-drain active-high fault output for thermal shutdown and protection events |+| 6 | ENABLE | input | PWM enable logic input; high enables phase drivers, low enters sleep mode after 1-3 ms |+| 7 | DIR | input | Motor direction control logic input for commutation direction selection |+| 8 | BRAKEn | input | Active-low brake logic input that shorts all low-side drivers to LSS, overriding ENABLE and SPEED |+| 9 | HA | input | Hall sensor input phase A with internal 100 kΩ pull-up to VDD |+| 10 | HB | input | Hall sensor input phase B with internal 100 kΩ pull-up to VDD |+| 11 | HC | input | Hall sensor input phase C with internal 100 kΩ pull-up to VDD |+| 12 | LSS | input | Low-side current sense terminal for external resistor (200-500 mV drop) or ground connection |+| 13 | GLC | output | Low-side gate driver output phase C, minimum voltage VREG - 0.2 V at 10 µA load |+| 14 | GHC | output | High-side gate driver output phase C, minimum voltage Cx - 0.2 V with charged bootstrap capacitor |+| 15 | SC | power_in | Phase C high-side source connection providing negative supply for high-side gate driver |+| 16 | CC | power_out | Phase C bootstrap supply node for capacitor and high-side gate driver |+| 17 | GLB | output | Low-side gate driver output phase B, minimum voltage VREG - 0.2 V at 10 µA load |+| 18 | GHB | output | High-side gate driver output phase B, minimum voltage Cx - 0.2 V with charged bootstrap capacitor |+| 19 | SB | power_in | Phase B high-side source connection providing negative supply for high-side gate driver |+| 20 | CB | power_out | Phase B bootstrap supply node for capacitor and high-side gate driver |+| 21 | GLA | output | Low-side gate driver output phase A, minimum voltage VREG - 0.2 V at 10 µA load |+| 22 | GHA | output | High-side gate driver output phase A, minimum voltage Cx - 0.2 V with charged bootstrap capacitor |+| 23 | SA | power_in | Phase A high-side source connection providing negative supply for high-side gate driver |+| 24 | CA | power_out | Phase A bootstrap supply node for capacitor and high-side gate driver |+| 25 | VREG | power_out | Regulated gate drive supply output, 7.0 V to 13.75 V depending on VBB input voltage |+| 26 | CP2 | passive | Charge pump capacitor terminal; connect 0.47 µF ceramic capacitor between CP1 and CP2 |+| 27 | CP1 | passive | Charge pump capacitor terminal; connect 0.47 µF ceramic capacitor between CP1 and CP2 |+| 28 | GND | power_in | Ground connection for logic and power return |+| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Allegro MicroSystems LLC |+| Package | QFN-28-EP(5x5) |+| Category | Motor Driver ICs |+| Pins | 29 |++## CAD (KiCad official)++- Symbol: `A4915METTR-T`+- Footprint: `Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm`+- 3D model: QFN-28-EP(5x5) (KiCad packages3D, STEP)+- 3D model files: `a4915mettr-t-etched.step` / `a4915mettr-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `a4915mettr-t.step` / `a4915mettr-t.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Allegro MicroSystems LLC datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588881674612445184) (17 pp, sha256 `e79f8d6c07a605a0`, retrieved 2026-09-22, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/a4915mettr-t-datasheet.pdf)
page.jsonadded+270
@@ -0,0 +1,270 @@+{+  "slug": "a4915mettr-t",+  "version": "0.1.0",+  "type": "component",+  "description": "Allegro MicroSystems LLC Brushless DC (BLDC) Motor Driver, QFN-28-EP(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "motor driver ics",+    "a4915mettr-t",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "a4915mettr-t.kicad_sym",+    "a4915mettr-t.kicad_mod",+    "a4915mettr-t.glb",+    "a4915mettr-t.step",+    "a4915mettr-t.lbr",+    "docs/hero.png",+    "docs/a4915mettr-t-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "A4915METTR-T",+    "manufacturer": "Allegro MicroSystems LLC",+    "package": "QFN-28-EP(5x5)",+    "pin_count": 29,+    "category": "Motor Driver ICs",+    "subcategory": "Brushless DC (BLDC) Motor Driver",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588881674612445184",+    "parts": {+      "symbol": "a4915mettr-t.kicad_sym",+      "footprint": "a4915mettr-t.kicad_mod",+      "model_3d": "a4915mettr-t-etched.glb",+      "model_3d_plain": "a4915mettr-t.glb",+      "model_3d_step": "a4915mettr-t-etched.step",+      "model_3d_step_plain": "a4915mettr-t.step",+      "lbr": "a4915mettr-t.lbr"+    },+    "distributor_links": {+      "lcsc": "C136637"+    },+    "pins": [+      {+        "number": "1",+        "name": "VBB",+        "type": "power_in",+        "description": "Power supply input, 5 V to 50 V operating range"+      },+      {+        "number": "2",+        "name": "SPEED",+        "type": "input",+        "description": "PWM duty cycle analog input, 0 V to VDD; output enabled above 79% VDD, disabled below 20% VDD"+      },+      {+        "number": "3",+        "name": "TDEAD",+        "type": "input",+        "description": "Dead time setting terminal with external resistor 12 kΩ to 220 kΩ connected to ground"+      },+      {+        "number": "4",+        "name": "VDD",+        "type": "power_in",+        "description": "Logic supply voltage input, 3 V to 5.5 V operating range"+      },+      {+        "number": "5",+        "name": "FAULT",+        "type": "output",+        "description": "Open-drain active-high fault output for thermal shutdown and protection events"+      },+      {+        "number": "6",+        "name": "ENABLE",+        "type": "input",+        "description": "PWM enable logic input; high enables phase drivers, low enters sleep mode after 1-3 ms"+      },+      {+        "number": "7",+        "name": "DIR",+        "type": "input",+        "description": "Motor direction control logic input for commutation direction selection"+      },+      {+        "number": "8",+        "name": "BRAKEn",+        "type": "input",+        "description": "Active-low brake logic input that shorts all low-side drivers to LSS, overriding ENABLE and SPEED"+      },+      {+        "number": "9",+        "name": "HA",+        "type": "input",+        "description": "Hall sensor input phase A with internal 100 kΩ pull-up to VDD"+      },+      {+        "number": "10",+        "name": "HB",+        "type": "input",+        "description": "Hall sensor input phase B with internal 100 kΩ pull-up to VDD"+      },+      {+        "number": "11",+        "name": "HC",+        "type": "input",+        "description": "Hall sensor input phase C with internal 100 kΩ pull-up to VDD"+      },+      {+        "number": "12",+        "name": "LSS",+        "type": "input",+        "description": "Low-side current sense terminal for external resistor (200-500 mV drop) or ground connection"+      },+      {+        "number": "13",+        "name": "GLC",+        "type": "output",+        "description": "Low-side gate driver output phase C, minimum voltage VREG - 0.2 V at 10 µA load"+      },+      {+        "number": "14",+        "name": "GHC",+        "type": "output",+        "description": "High-side gate driver output phase C, minimum voltage Cx - 0.2 V with charged bootstrap capacitor"+      },+      {+        "number": "15",+        "name": "SC",+        "type": "power_in",+        "description": "Phase C high-side source connection providing negative supply for high-side gate driver"+      },+      {+        "number": "16",+        "name": "CC",+        "type": "power_out",+        "description": "Phase C bootstrap supply node for capacitor and high-side gate driver"+      },+      {+        "number": "17",+        "name": "GLB",+        "type": "output",+        "description": "Low-side gate driver output phase B, minimum voltage VREG - 0.2 V at 10 µA load"+      },+      {+        "number": "18",+        "name": "GHB",+        "type": "output",+        "description": "High-side gate driver output phase B, minimum voltage Cx - 0.2 V with charged bootstrap capacitor"+      },+      {+        "number": "19",+        "name": "SB",+        "type": "power_in",+        "description": "Phase B high-side source connection providing negative supply for high-side gate driver"+      },+      {+        "number": "20",+        "name": "CB",+        "type": "power_out",+        "description": "Phase B bootstrap supply node for capacitor and high-side gate driver"+      },+      {+        "number": "21",+        "name": "GLA",+        "type": "output",+        "description": "Low-side gate driver output phase A, minimum voltage VREG - 0.2 V at 10 µA load"+      },+      {+        "number": "22",+        "name": "GHA",+        "type": "output",+        "description": "High-side gate driver output phase A, minimum voltage Cx - 0.2 V with charged bootstrap capacitor"+      },+      {+        "number": "23",+        "name": "SA",+        "type": "power_in",+        "description": "Phase A high-side source connection providing negative supply for high-side gate driver"+      },+      {+        "number": "24",+        "name": "CA",+        "type": "power_out",+        "description": "Phase A bootstrap supply node for capacitor and high-side gate driver"+      },+      {+        "number": "25",+        "name": "VREG",+        "type": "power_out",+        "description": "Regulated gate drive supply output, 7.0 V to 13.75 V depending on VBB input voltage"+      },+      {+        "number": "26",+        "name": "CP2",+        "type": "passive",+        "description": "Charge pump capacitor terminal; connect 0.47 µF ceramic capacitor between CP1 and CP2"+      },+      {+        "number": "27",+        "name": "CP1",+        "type": "passive",+        "description": "Charge pump capacitor terminal; connect 0.47 µF ceramic capacitor between CP1 and CP2"+      },+      {+        "number": "28",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection for logic and power return"+      },+      {+        "number": "29",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 29 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 17,+        "cost_usd": 0.3651,+        "at": "2026-09-22T12:11:55"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588881674612445184",+        "pages": 17,+        "sha256": "e79f8d6c07a605a0",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 29,+        "described": 29,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file