← Commit history

Initial commit: component/a1335lletr-t

Ray ·e563175b54 ·
2 files changed +227
README.mdadded+50
@@ -0,0 +1,50 @@+# A1335LLETR-T++**Allegro MicroSystems LLC** · Position Sensors · TSSOP-14++A1335LLETR-T from Allegro MicroSystems LLC, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | DGND | power_in | Digital ground terminal. |+| 2 | BYP | power_out | Internal bypass node; connect 0.1 µF capacitor to DGND for power supply filtering. |+| 3 | DGND | power_in | Digital ground terminal. |+| 4 | NC | unconnected | Not Connected; connect to GND for ESD protection. |+| 5 | VCC | power_in | Power supply input, 4.5 to 5.5 V nominal, also used for EEPROM writing pulses and Manchester serial interface. |+| 6 | NC | unconnected | Not Connected; connect to GND for ESD protection. |+| 7 | AGND | power_in | Analog ground terminal. |+| 8 | ISEL | input | Interface mode selection input; set low for I2C/SENT mode or high for SPI mode. |+| 9 | SENT | tri_state | SENT transmission output terminal (open-drain); requires pull-up resistor 5 to 50 kΩ to supply voltage. |+| 10 | SDA/MISO | bidirectional | I2C data terminal and SPI MISO (open-drain); bidirectional in I2C mode with external pull-up to 3.3 V required. |+| 11 | SCL/SCLK | input | Serial clock input (I2C: SCL maximum 400 kHz, SPI: SCLK maximum 10 MHz) with external pull-up to 3.3 V required. |+| 12 | SA1/MOSI | input | I2C slave address bit 1 input (tie to BYP for 1 or DGND for 0); SPI Master Output/Slave Input terminal; Manchester protocol MSB. |+| 13 | SA0/CS | input | I2C slave address bit 0 input (tie to BYP for 1 or DGND for 0); SPI active-low chip select input; Manchester protocol LSB. |+| 14 | DGND | power_in | Digital ground terminal. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Allegro MicroSystems LLC |+| Package | TSSOP-14 |+| Category | Sensors |+| Pins | 14 |++## CAD (KiCad official)++- Symbol: `A1335LLETR-T`+- Footprint: `Package_SO:TSSOP-14_4.4x5mm_P0.65mm`+- 3D model: TSSOP-14 (KiCad packages3D, STEP)+- 3D model files: `a1335lletr-t-etched.step` / `a1335lletr-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `a1335lletr-t.step` / `a1335lletr-t.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Allegro MicroSystems LLC datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588942259765596160) (29 pp, sha256 `cae1cf85402d79ad`, retrieved 2026-09-21, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/a1335lletr-t-datasheet.pdf)
page.jsonadded+177
@@ -0,0 +1,177 @@+{+  "slug": "a1335lletr-t",+  "version": "0.1.0",+  "type": "component",+  "description": "Allegro MicroSystems LLC Position Sensors, TSSOP-14. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "sensors",+    "a1335lletr-t",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "a1335lletr-t.kicad_sym",+    "a1335lletr-t.kicad_mod",+    "a1335lletr-t.glb",+    "a1335lletr-t.step",+    "a1335lletr-t.lbr",+    "docs/hero.png",+    "docs/a1335lletr-t-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "A1335LLETR-T",+    "manufacturer": "Allegro MicroSystems LLC",+    "package": "TSSOP-14",+    "pin_count": 14,+    "category": "Sensors",+    "subcategory": "Position Sensors",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588942259765596160",+    "parts": {+      "symbol": "a1335lletr-t.kicad_sym",+      "footprint": "a1335lletr-t.kicad_mod",+      "model_3d": "a1335lletr-t-etched.glb",+      "model_3d_plain": "a1335lletr-t.glb",+      "model_3d_step": "a1335lletr-t-etched.step",+      "model_3d_step_plain": "a1335lletr-t.step",+      "lbr": "a1335lletr-t.lbr"+    },+    "distributor_links": {+      "lcsc": "C2655192"+    },+    "pins": [+      {+        "number": "1",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground terminal."+      },+      {+        "number": "2",+        "name": "BYP",+        "type": "power_out",+        "description": "Internal bypass node; connect 0.1 µF capacitor to DGND for power supply filtering."+      },+      {+        "number": "3",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground terminal."+      },+      {+        "number": "4",+        "name": "NC",+        "type": "unconnected",+        "description": "Not Connected; connect to GND for ESD protection."+      },+      {+        "number": "5",+        "name": "VCC",+        "type": "power_in",+        "description": "Power supply input, 4.5 to 5.5 V nominal, also used for EEPROM writing pulses and Manchester serial interface."+      },+      {+        "number": "6",+        "name": "NC",+        "type": "unconnected",+        "description": "Not Connected; connect to GND for ESD protection."+      },+      {+        "number": "7",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground terminal."+      },+      {+        "number": "8",+        "name": "ISEL",+        "type": "input",+        "description": "Interface mode selection input; set low for I2C/SENT mode or high for SPI mode."+      },+      {+        "number": "9",+        "name": "SENT",+        "type": "tri_state",+        "description": "SENT transmission output terminal (open-drain); requires pull-up resistor 5 to 50 kΩ to supply voltage."+      },+      {+        "number": "10",+        "name": "SDA/MISO",+        "type": "bidirectional",+        "description": "I2C data terminal and SPI MISO (open-drain); bidirectional in I2C mode with external pull-up to 3.3 V required."+      },+      {+        "number": "11",+        "name": "SCL/SCLK",+        "type": "input",+        "description": "Serial clock input (I2C: SCL maximum 400 kHz, SPI: SCLK maximum 10 MHz) with external pull-up to 3.3 V required."+      },+      {+        "number": "12",+        "name": "SA1/MOSI",+        "type": "input",+        "description": "I2C slave address bit 1 input (tie to BYP for 1 or DGND for 0); SPI Master Output/Slave Input terminal; Manchester protocol MSB."+      },+      {+        "number": "13",+        "name": "SA0/CS",+        "type": "input",+        "description": "I2C slave address bit 0 input (tie to BYP for 1 or DGND for 0); SPI active-low chip select input; Manchester protocol LSB."+      },+      {+        "number": "14",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground terminal."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 29,+        "cost_usd": 0.3505,+        "at": "2026-09-21T20:49:43"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588942259765596160",+        "pages": 29,+        "sha256": "cae1cf85402d79ad",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 14,+        "described": 14,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file