component
5P49V5901B000NLGI8
Public Made by Adomby adom
RENESAS Clock Generators, PLLs, Frequency Synthesizers, QFN-24(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+66@@ -0,0 +1,66 @@+# 5P49V5901B000NLGI8++**RENESAS** · Clock Generators, PLLs, Frequency Synthesizers · QFN-24(4x4)++5P49V5901B000NLGI8 from RENESAS, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | CLKIN | input | Differential clock input (true). Accepts LVDS/LVPECL/HCSL differential clocks or single-ended reference from 1 MHz to 350 MHz. Weak internal 100 kΩ pull-down. |+| 2 | CLKINB | input | Complementary differential clock input (inverting half of CLKIN pair). Weak internal 100 kΩ pull-down. |+| 3 | XOUT | output | Crystal oscillator interface output. Connect to the far side of an 8-40 MHz fundamental-mode quartz crystal (paired with XIN/REF); leave floating if the crystal oscillator is not used. |+| 4 | XIN/REF | input | Crystal oscillator input, or single-ended LVCMOS reference clock input (1-200 MHz). When overdriven as REF, keep input voltage ≤ 1.2 V max (see 'Overdriving the XIN/REF Interface'). |+| 5 | VDDA | power_in | Analog PLL power supply. 1.8 V, 2.5 V, or 3.3 V; must be the same voltage as VDDD. |+| 6 | CLKSEL | input | Input reference select in manual switchover mode. 0 = XIN/REF+XOUT (default); 1 = CLKIN/CLKINB. Polarity is reprogrammable via I2C (see Table 4). Weak internal pull-down. |+| 7 | SD/OE | input | Dual-function shutdown / output-enable. SH bit selects mode; SP bit sets OE polarity (default active-LOW). In SD, chip shuts down (differential outputs driven high/low, LVCMOS outputs driven low); in OE, disabled outputs can be tri-stated or driven per programming. Weak internal pull-down. |+| 8 | SEL1/SDA | bidirectional | Configuration select bit 1, or I2C SDA data line. Function is chosen at power-up by the OUT0_SEL_I2CB latched pin. Weak internal pull-down. |+| 9 | SEL0/SCL | bidirectional | Configuration select bit 0, or I2C SCL clock line. Function is chosen at power-up by the OUT0_SEL_I2CB latched pin. Weak internal pull-down. |+| 10 | VDDO4 | power_in | Output-bank 4 power supply. 1.8-3.3 V; sets the output voltage/standard for OUT4/OUT4B. |+| 11 | OUT4 | output | Clock output 4 (true). Configurable as one differential pair with OUT4B (LVPECL/LVDS/HCSL) or as one of two independent LVCMOS outputs. |+| 12 | OUT4B | output | Complementary clock output 4 (inverting/second half of OUT4 pair). |+| 13 | OUT3B | output | Complementary clock output 3 (inverting/second half of OUT3 pair). |+| 14 | OUT3 | output | Clock output 3 (true). Configurable as one differential pair with OUT3B or as two independent LVCMOS outputs. |+| 15 | VDDO3 | power_in | Output-bank 3 power supply. 1.8-3.3 V; sets the output voltage/standard for OUT3/OUT3B. |+| 16 | OUT2B | output | Complementary clock output 2 (inverting/second half of OUT2 pair). |+| 17 | OUT2 | output | Clock output 2 (true). Configurable as one differential pair with OUT2B or as two independent LVCMOS outputs. |+| 18 | VDDO2 | power_in | Output-bank 2 power supply. 1.8-3.3 V; sets the output voltage/standard for OUT2/OUT2B. |+| 19 | OUT1B | output | Complementary clock output 1 (inverting/second half of OUT1 pair). |+| 20 | OUT1 | output | Clock output 1 (true). Configurable as one differential pair with OUT1B or as two independent LVCMOS outputs. |+| 21 | VDDO1 | power_in | Output-bank 1 power supply. 1.8-3.3 V; sets the output voltage/standard for OUT1/OUT1B. |+| 22 | VDDD | power_in | Digital core power supply. 1.8 V, 2.5 V, or 3.3 V; must be the same voltage as VDDA. |+| 23 | VDDO0 | power_in | Power supply for the OUT0_SEL_I2CB LVCMOS reference output driver. 1.8-3.3 V; sets output voltage level for OUT0. |+| 24 | OUT0_SEL_I2CB | bidirectional | Latched-input / LVCMOS-output triple-function pin. At power-up, the pin is sampled: a weak 10 kΩ pull-up configures pins 8/9 as SEL1/SEL0 (hardware config select); a weak 10 kΩ pull-down or floating configures pins 8/9 as I2C SDA/SCL. After power-up, the pin drives an LVCMOS reference clock output (OUT0). |+| EPAD | GND | power_in | Exposed thermal/ground pad on the package underside. Must be connected to the PCB ground plane for both electrical ground and thermal dissipation. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | RENESAS |+| Package | QFN-24(4x4) |+| Category | Clock/Timing |+| Pins | 25 |++## Ordering variants++Same part, different packaging or reel option.++- `5P49V5901B000NLGI8`++## CAD (KiCad official)++- Symbol: `5P49V5901B000NLGI8`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm`+- 3D model: QFN-24(4x4) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [RENESAS datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8600773965388259328) (None pp, sha256 `220fbf224fae5a9c`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/5p49v5901b000nlgi8-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "5p49v5901b000nlgi8",+ "version": "0.1.0",+ "type": "component",+ "description": "RENESAS Clock Generators, PLLs, Frequency Synthesizers, QFN-24(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "clock-timing",+ "5p49v5901b000nlgi8"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "5p49v5901b000nlgi8.kicad_sym",+ "5p49v5901b000nlgi8.kicad_mod",+ "5p49v5901b000nlgi8.glb",+ "5p49v5901b000nlgi8.step",+ "5p49v5901b000nlgi8.lbr",+ "docs/hero.png",+ "docs/5p49v5901b000nlgi8-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}